Terry violet bead

To make a terry violet made of beads: - Beads No. 10 of the preferred color, in this case blue, blue, green and a little yellow; - Wire 0.2 or 0.3 mm thick; - Florlenta or green floss threads; - Clay Moment and PVA; - Gypsum or alabaster; - A small flower pot or, if not, some kind of dish; - Green acrylic paint or gouache; - A piece of green sisal. Violet is made in the loop technique. Flowers will be 9 pieces, but you can do more. Each individual flower is woven immediately whole, so we cut off the wire about 60-70 cm at once, so that it would be enough and not necessary, then put the pieces together. We string 6 blue beads on a wire and twist them into a loop.
 Terry violet of beads
a couple of turns, departing from the end of the wire 10 see. For the next loop, which will pass over the first one, we type approximately 15-17 pieces.and twist at the base.
 Terry violet of beads
Make a similar loop once again with lots of beads.
Terry violet of beads
To make fringe on the petals you need a bead of contrasting color, in this case it's blue. At the long end of the wire we collect an approximate amount of beads and pass it under the last loop of the petal.
 Terry violet from beads
We measure 6-7 blue beads and we fix tightly the wire between the 5 and 6 blue beads on the petal itself.
 Terry Violet Bead
So you need to do 5 times so that at the end of radiated "fringe".
 Terry Violet Beaded
At the end we fix the wire at the base as usual. On the remaining working piece of wire it is necessary to weave 4 more similar petals.To do this, retreat from the first one approximately 1 cm and weave according to the first one.
 Terry violet from beads
Terry violet of beads It turns out 5 petals and 2 remaining ends of the wire that you should not twist together yet.
 Terry Violet Bead
Now you need to make yellow stamens. Everything is performed in the same loop technique.
 Terry Violet Bead
Next, insert the wire with stamens into the middle of the flower, then twist the ends of the wire together while straightening even petals.
 Terry Violet Bead
By the way, one flower can be made in the form of an unopened bud. Leaflet . Now proceed to the production of leaflets. For this you need beads of dark green and light green color, but you can make one-colored.Dark will go along the edge of the leaf and inside in the form of dots. We shall weave on the technique of the French weaving. First you need to cut the wire about 60 cm., Retreat from one end of 15 cm, and loop it.
 Terry Violet Bead
The hinge itself will be a leg, we do not need it yet, we'll weave the sheet itself on a short single piece of wire - this will be the basis, the long segment will be working. 13 beads are strung on the base.
 Terry Violet Bead
String a random amount of beads on a long working end. Raise it up to the base and connect it closely at a 45-degree angle by twisting at the top in one turn.
 Terry Violet Bead
Then the wire we lower down to the loop and twist in two turns.
 Terry violet bead
Since the leaf will be carved, we will do this further.Stringing the beads over the long end of the wire and passing it under the loop, after which we tightly pass this wire between the beads.
 Terry Violet Bead
That do the same in the reverse order to the loop.
 Terry violet bead
So we continue to do this several times until we get 5 notches on each side fox ika. When it is ready, the base will need to be carefully cut, leaving 0.5 cm of wire, which should be bent to the wrong side.
 Terry bead violet
Terry violet from beads
There are 9 pieces to make leaves, but you can make a different quantity. Now you need to wrap the legs of the leaves and flowers with green florlenta or, who does not have it, with green floss threads in several additions, after you have left the wire with PVA glue.
Terry violet from beads
Cut a small piece of tape and stick the side of the flowers and leaves from the base along the curve with a sticky side.So wrap all the details.
 Terry Violet Beaded
 Violet Veil of Beads
To form a violet, we twist together 3-4 flowers with the same florlenta, we get 3 groups, which can also be joined together.
 Terry Violet Bead
Now you need to attach to a bunch of leaves. We will do this in 2 tiers. The first will be 4 sheets, the second - 5.
 Violet Veil of Beads
The output will be a bunch of violets, which will now need to be planted in pot. Design. If there is no pot, do not despair. Everyone in the house has cylinders, for example, from under the foam or similar, here is the cap from it in this case will be used. It will plant a flower in alabaster or gypsum, which must be diluted with warm water to a thickness of sour cream.
 Violet Veil of Beads